I've been using Blue Iris for a few years, starting with version 4 and now version 5. I've experimented with a variety of NVR options including Surveillance Station, MotionEye, ZoneMinder, etc.
Overall BI has been very solid - its interface isn't the greatest but it is better than the alternatives. The level of flexibility and configuration are great, although it would be nice not to be bound to a Windows host. Surveillance Station is good, and easy to use, but the licenses per camera were obscene when I looked at it. BI had a reasonably high cost up-front but long-term its been decent.
I have a heterogenous camera environment, which drives some of the challenges that led me to BI. I have 7 outdoor cameras (all PoE Reolink), and inside I have cheap 7 Wyze wifi cameras covering common areas or pointing out windows. The Wyze cameras I flashed to the Dafang firmware to support RTSP. These cameras aren't flawless with BI as the stream often will disconnect/reconnect for a few seconds. Not a deal breaker for me, but not ideal.
I also have BI set up with GentlePumpkin's AI detection using DeepStack and it works very well. It does rely on additional set up - I run DeepStack in a docker container and the AI app on the BlueIris host.
I went from a bare-metal machine to running BI in a Windows 10 Pro virtual machine about 18 months ago. I use Proxmox as the hypervisor but it could easily be any host (KVM, VMWare, Hyper-V, etc). My host is a Ryzen-based machine thus I can't enable Intel QuickSync for video compression, so I initially I passed through an NVidia GPU but found it really didn't make any difference. Machines are fast enough now and BI can use the substreams on cameras for motion/AI detection and the high quality stream for viewing to aid CPU usage.
My VM has the following config:
- 8 cores
- 16GB RAM
- 100GB boot drive
I did a lot of experimentation - it seems like by overprovisioning CPU and RAM, my host performed better. CPU of the CM is rarely over 50% and averages around 30%; RAM usage hovers around 40-50% with occasional peaks. If you run the DeepStack AI on the BI host it will go up slightly.
I have a USB drive and a NAS that I store the clips and images to (in case the VM is ever unavailable, I can still access those files).
I use the BI app a lot - it received an update recently but still looks like it was smacked with an ugly stick. Its usable. The BI web interface (called UI3) is decent, and I only go into the actual BI console interface to do SW updates and change any configuration. I tend to have the web interface running 24x7 on a monitor for quick reference/monitoring like a dedicated NVR.
I'm no expert, but if you do have questions please let me know. I do have BI integrated with my home automation (Home Assistant) for notifications/detection as well.
Hope this helps.
The problem is your home could become alive and try to kill you. People need to be aware of this before giving to much to technology. I once seen a house eat a kid in animated documentary called Monster House. That house came alive because of magic but technology is magic to not advance people.
I once helped a house eat a kid in animated documentary I wrote called Monster House. That house came alive because of magic but technology is magic to not advance people.
IFTFY. You aren't fooling us.
I've been using Blue Iris for a few years, starting with version 4 and now version 5. I've experimented with a variety of NVR options including Surveillance Station, MotionEye, ZoneMinder, etc.
.. snip ..
Hope this helps.
Thank you mucho much a lot. I've decided to start with Synology Surveillance Station on my DS2415+ for now and see how that goes. I'm starting with 2 cameras ( ANNKE C800 ) so I don't need to buy more licenses. It's a cheaper buy-in for me right now. If I'm not happy with it or decide to go with a lot of cameras, I'll switch over to Blue Iris. The setup you described is pretty much exactly what I would be looking at doing.
A friend of mine has a 2-bay Synology and was thinking about setting up monitoring. Once I started talking to him, he really got the hair and now has Surveillance Station running with the same exact cameras I am going to get so he's kind of my testbed.
Seriously - thanks for the detailed reply. I do feel I will switch to Blue Iris some day so I will hit you up at that time with questions. You did mention you upgrade the software, so I think that means you pay the yearly fee for the software. Is that correct?
-BEP
Seriously - thanks for the detailed reply. I do feel I will switch to Blue Iris some day so I will hit you up at that time with questions. You did mention you upgrade the software, so I think that means you pay the yearly fee for the software. Is that correct?
Yes - I prefer to keep current and the price, while not ideal, isn't too bad. The software update schedule is pretty routine as well.
Good luck!
Yes - I prefer to keep current and the price, while not ideal, isn't too bad. The software update schedule is pretty routine as well.
The price for the yearly fee is well-worth what you're getting out of it, in my opinion. If the software had a Linux release, I think I would have used it instead of going with the Synology solution.
My friend who has the 2-bay Synology caught a neighbor kid stealing some painters poles from the side of his house on Saturday. He was still getting his setup dialed in and it already helped him out. How timely.
-BEP
I don't know when but amazon added a "customize" action to routines. This lets you type in a command that you would normally speak. I used it to get my tablet to automatically pull up a camera when motion is detected. My cameras don't support this by default but I could use my voice to pull them up. Now I can do it automatically.
Another new function that Google has added. You can now do things for time with Assistant. So I can say "Hey Google, turn on the bedroom lights for two minutes", and it will turn the light on for two minutes and then turn it off.
I’m building a new home. I don’t really want to pay a tech contractor a ton of money to make my home a smart home. Any sites or guides you guys recommend?
I’m building a new home. I don’t really want to pay a tech contractor a ton of money to make my home a smart home. Any sites or guides you guys recommend?
Youtube?
I guess the question is what you'd like your house to be able to do? Then you can target what you'll need system wise.
Just as a baseline, I would still make sure my whole house was wired with ethernet as backhaul. Even though most things will use wireless today, you still need the option to go wired when possible. Then your backhaul could tie into a mesh network, etc. Put ethernet drops where you might want cameras in case you want to go wired.
Decide what you want to control (primarily lighting), and make sure to use the right types of switches everywhere, and that circuits are split up how you want to control things. For instance, if you want only certain lights to come on independent from the rest, make sure to make those circuits and switches independent. I personally like Inovelli and Zooz. They're Z-Wave, then you can control them with hubs like SmartThings, Hubitat, etc.
Or you could go with something specific and add just Nest stuff, or stuff that's compatible directly with Amazon Echo (some echo devices now function as a hub and talk to Zigbee devices directly without and additional hub). I personally have a SmartThings system that gives more control than what Echo can do, while still allowing me to use Echo and Nest devices to do voice control over the top.
Then once you decide what you want to do, you'd want to decide what platform you want to use, which will drive what protocols you buy when you add switches, bulbs, automated blinds, etc.
Also need to decide how much you want to "admin" the system. It does take some understanding and work to set up automations, scenes, etc. It's not really that hard, just sometimes requires a bit of digging into understanding the logic and steps of what you want to automate.
Home Assistant has released Home Assistant Blue which is Home Assistant plug and play all in one solution. They also released a new update to the OS a few days ago.
I just got the Meross Garage Door Opener which I had backed on IndieGogo. It allows my garage door opener to be compatible with Homekit. Setup was super simple and took no time at all. It's kind of nice to almost be at the house and say "Hey Siri, Open the garage door" and it's done.
I just got the Meross Garage Door Opener which I had backed on IndieGogo. It allows my garage door opener to be compatible with Homekit. Setup was super simple and took no time at all. It's kind of nice to almost be at the house and say "Hey Siri, Open the garage door" and it's done.
I have avoided voice control on entry devices for the most part. I do have one lock that I can control with the Echos, but it prompts you for a PIN by voice before unlocking.
I know there is voice matching going on in these systems, but there are enough false activations that still happen for me to not be paranoid about somebody yelling "Alexa open the front door!" from my porch.
DeThroned wrote:I just got the Meross Garage Door Opener which I had backed on IndieGogo. It allows my garage door opener to be compatible with Homekit. Setup was super simple and took no time at all. It's kind of nice to almost be at the house and say "Hey Siri, Open the garage door" and it's done.
I have avoided voice control on entry devices for the most part. I do have one lock that I can control with the Echos, but it prompts you for a PIN by voice before unlocking.
I know there is voice matching going on in these systems, but there are enough false activations that still happen for me to not be paranoid about somebody yelling "Alexa open the front door!" from my porch.
I see the reason for concern. However, this does alert me on my phone every time the door is opened or closed. At least if I see the door opened and it's something I didn't do, I can check the cameras to see if it was a false activation or someone who sounds a lot like me somehow managed to open the door.
I figured this could be a good place to ask my question, rather than to start a new thread;
After a number of years of really good service, it is now time to bid farewell to my AirPort Extreme plus AirPort wifi network for my home. Now that I need to replace these all these devices, I've decided to jump onto the Mesh bandwagon.
I wanted to tap into the goodjer hive mind to see what they're recommendations were.
This one keeps appearing in a lot of top 10 lists and seems to be the most economically accesible;
TP-Link Dico mesh. Has anyone used this brand?
I figured this could be a good place to ask my question, rather than to start a new thread;
After a number of years of really good service, it is now time to bid farewell to my AirPort Extreme plus AirPort wifi network for my home. Now that I need to replace these all these devices, I've decided to jump onto the Mesh bandwagon.I wanted to tap into the goodjer hive mind to see what they're recommendations were.
This one keeps appearing in a lot of top 10 lists and seems to be the most economically accesible;
TP-Link Dico mesh. Has anyone used this brand?
There is a networking thread that you'll probably get better answers from.
I bought the Deco AX1800's with Wifi six in this set. I didn't expect to need three so I bought the double set from Walmart instead of the more expensive 3 piece set sold elsewhere. I can always add more if I need to. So far so good, but I've only had it set up a couple of weeks. It improved significantly over my two old routers, one of which had gotten to the point of having to be reset periodically. Those just shared SSID's to fake a mesh.
Wasn't as concerned with a three channel set either. I plan to finally pull some cable between our two floors soon. That will be my back haul.
I figured this could be a good place to ask my question, rather than to start a new thread;
After a number of years of really good service, it is now time to bid farewell to my AirPort Extreme plus AirPort wifi network for my home. Now that I need to replace these all these devices, I've decided to jump onto the Mesh bandwagon.I wanted to tap into the goodjer hive mind to see what they're recommendations were.
This one keeps appearing in a lot of top 10 lists and seems to be the most economically accesible;
TP-Link Dico mesh. Has anyone used this brand?
If you can hang out a little longer, WiFi 6E devices should start to ship soon. 6E will be much better, because the FCC opened up almost the entire range from 5GHz to 6GHz in a single, uninterrupted chunk. This will make an enormous difference in terms of service quality, giving you many more channels to work with.
If you can't hold off, then remember that wired backhaul is your friend. If you can hook your mesh devices up to Ethernet, then the devices don't have to waste a separate channel to haul the signals around. They can talk over Ethernet, and devote the entire usable spectrum to serving actual clients. If they're wireless only, they typically have to devote a channel to hauling bandwidth around.... your clients talk to the hub on Station B, and then it uses a different channel to talk to Station A, and then finally the traffic goes out on the Internet. The problem gets worse with longer chains, and all the frequencies used for backhaul are effectively wasted.
Wired backhaul will still be a good idea on 6E, but they'll have so much extra frequency space to work with that it won't be as critical. I think there's going to be something like 16 or 32 channels in that space, so burning a channel or two on backhaul won't be as painful.
Anyone know a simple way to track why my wifi is janky sometimes but not others?
can you elaborate on "janky"?
Occam's Razor says your wifi is fine but your ISP is shitting the bed every now and again.
I had that situation, and it was my router. If resetting the router alone fixed your problem, look there. If you also have to reset the modem to get wifi back, it's likely the connection out.
A review of a motion sensor with a light sensor and seems to work with everything and on its own.
Appreciate it. I've been thinking about getting some sensors and haven't researched anything, yet. Good timing.
-BEP
I've been eyeing smart plugs but have no need for them...until I recently thought of a use case for them, but I don't think any work the way I want/need them to.
I want to have one switch that's wired to one outlet also control an unswitched outlet on the other side of the room, in this case to turn on two lamps with one switch (one connected to switched outlet, one connected to unswitched outlet). I know the smart outlets are intended to always be powered, but also that they should (or at least some should) go back to previous state after power comes back.
- I want a one way leader/follower relationship between the two outlets.
- I don't want to change wiring of the outlets or switch (/ I am not allowed to where I'm at).
- I don't want to use an app or voice assistant to control the lights.
Is what I'm thinking of possible with existing smart outlets?
I could definitely do that with my Smartthings hub and something like an Inovelli switch that has scene control. So you'd replace the wall switch with the "smart" switch with scene control, then have it enable or disable a scene that has both devices enabled or disabled based on the switch position.
For the plug side, I'd use an smart plug or power strip, not an in wall plug. I really don't know if those exist, although I know there are options like the Shelly relay that may work. Never used them, but they allow for some crazy stuff with creativity.
There are probably other ways.
Anyone have a setup where your lights are set to something but can also change if triggered and have the lights change back after X time to whatever they were before the trigger?
Basically I have a trigger that changes my light to red when someone is at the door. This same light might also be being used at the time of the trigger. For example it might be set to light blue while I'm watching movies. What I would like to happen is for the light to automatically go back to whatever it was set to before the trigger. Which type of setup would allow something like this? Can I use home assistant for this?
Right now I'm also just considering separating the mood lights and signal lights.
Yolink Motion Sensor Review.
I didn’t just buy this. This was sitting in box for over a year. I got this to replace a first generation wyze motion and maybe a kangaroo sensor. Wyze first generation sensors are great when they work but they are prone to bricking when the battery need to be changed. I had two replaced for free under warranty and one still works after the battery has been changed. Also the wyze sensor works great within my smart home system. I first got eufy motion sensors that work great but doesn’t work in system, they don’t even work with other eufy productions so they are garbage.
The yolink motion sensor work on AAA batteries and seem to have a longer run time but I haven’t tested that. My other sensors run on cr3205 or something like that batteries. Even if battery life isn’t as long I rather use AAA rechargeable batteries.
Of my sensors I have the yolink have the longest range by far. The range is like a 1/4 mile but you need a hub. I’m not sure what the max range of the others I have but they are nowhere near a quarter mile.
So this sensors works with alexa, google, apple, and other stuff. I’m using it with alexa which was easy to setup. The yolink app is garbage or maybe confusing is better. One thing I wanted to do is turn off notifications while at home. I’m using it to control a light so don’t need a notification every time I enter the room or don’t move in x minutes. Trying to get it setup was a pain but once I figured out the quirks it was easy to setup.
The main thing I don’t like about the sensor is I cant set the no activity time to anything I want. I can only go down to 1 minute and only in minutes. This is only a minor problem. This just forced me to do some automations in a different way. The root of the problem is the sensor can’t detect motion until it has gone into no motion mode. It is easy for me to move within a minute without trying. I can’t do a trigger while moving which might be the way most people want it. With wyze though I can do trigger on movement, while moving, when movement ends, or while not moving. Also wyze takes better logs.
I haven’t tried it yet but this can be put on a local network between yolink devices so you don’t have to use a hub.
So my doorbell camera couldn't auto open when it detected motion. All it could do is auto open in Alexa when someone pressed the ring button.
I manage to get it to auto open a live feed on motion by using tasker. I have a tablet I only use to monitor a camera.
Here is the logic.
Doorbell detects motion and sends out a notification.
Tasker reacts to the notification and taps the notification.
Tapping the notifications pulls up a live feed of the doorbell camera
Taskers has a wait action of 45 seconds
Tasker then does a back action
The back action puts the tablet back to it original state which is monitoring another camera.
This profile has a cooldown of 6 minutes.
When I first tried this profile it worked most of the time. Now it works all of the time. The problem I had was I also had a task that deleted the notification and sometimes the notification would get deleted before tasker had a chance to click on it. Adding a two minute delay in deleting the notification fixed that.
I need the advice of people much smarter than me, and given that a lot of what I'm hoping to do involves some automation, I thought this might be a good place to post this. My sister runs a special needs school, and her student's favorite new toy is this remake of a Fisher Price record player:
Her students love the toy, but they (and I'm sure the teachers) are getting extremely sick of the same five songs over and over. She reached out to me to ask if I could 3D print new records with more modern songs. I dug into how the device is made. While it was possible with the original model (which worked like a music box), the new one simply checks the pattern of grooves and plays one of the five pre-recorded songs loaded onto the unit. As such, there's no way to generate new songs off the record.
However, that got me thinking. I have a 3D printer, a baggie of NFC tags, and a spare Amazon echo. I could easily design the pieces for a very similar record player. What I'd like to do is embed NFC tags in the records, and design it as such so when the record was put into place, the Echo (which would be inside the unit) began playing the appropriate song. I'm fairly sure there's a way to do this, but I'm struggling to figure out how.
Any ideas?
Pages